Baitcasters have several advantages over a spinning reel. They can handle a heavier line, and generally allow for longer casts. But if you don’t know how to use one correctly, you’re not going to be able to catch much with it.
That’s why we’ve put this article together, to explain to you exactly how to use your baitcaster as it’s meant to be used. We will go through everything step by step, starting with the basics. Read on to find out more!
Getting The Right Equipment
The first thing what is the point of a baitcaster? You need to do is get yourself a good rod. You want something that has some weight to it, so you can cast further than you would with an ordinary fishing rod.
If you are using a point of a baitcaster rod, make sure it’s at least 6 feet long, but preferably 7 or 8 feet.
Also need the point of a baitcaster itself. This is basically just a small motorized crank that turns the spool of your line.
The best ones are made from aluminum, because they are light, strong, and durable.
If you already own a point of a baitcasting reel, then great! Just attach the new motor to it.
If you don’t have a point of a baitcasting reel yet, then you should buy one. It won’t cost very much, and you’ll be glad you did.
Setting Up The point of a Baitcaster
Once you’ve got all the gear, you’re ready to set up the point of a baitcasterster.
You might think that you could simply attach the baitcaster directly to a spinning reel, but there are two problems with this approach…
First, most spin reels aren’t designed to take the extra strain of a heavy load, which means that they won’t last very long.
And secondly, when you are casting, you need to keep the reel in motion, otherwise the line will become tangled. With a baitcaster, however, you can stop turning the reel whenever you like, making it far more versatile.
So, what you should do is take off the cover plate that holds the motor in place. Then remove the two screws holding the motor housing in place.
Now, slide the motor out of the way, and unscrew the bottom half of the housing. Finally, screw the top half back onto the bottom half, and you’re done!
Now, you may notice that the motor isn’t attached to anything. That’s fine; you can leave it alone for now. What you really need to do next is attach the bail arm to the shaft of the motor. To do this, thread the bail arm into the hole where the motor shaft goes, and tighten it down as tight as possible.
Now, you need to connect the power cord to the battery pack. First, plug the power cord into the battery pack. Then, insert the other end of the cord into the socket on the side of the motor. Once again, tighten it down as tight as you can.
Finally, you need to connect a switch to the battery pack.
This allows you to turn the motor on and off.
Simply push the button on the side of the battery pack until it clicks into place, and then press it once to turn the motor on. Again, tighten it down as tightly as you can.
Now, you’re ready to start casting with your brand new baitcaster!
Casting With The Baitcaster
Once you have your rod and baitcaster properly set up, you need to learn how to cast properly…
There are many different techniques out there, but the basic idea is always the same – you need to start off slowly, then gradually increase your speed until you reach maximum velocity.
When you do this, you should feel the rod bend slightly under the force of the tensioned line.
The key thing here is to make sure that you get the right amount of line out before you start cranking away at full speed.
Too little line, and you won’t be able to control the lure or sinker. Too much line, and you’ll lose accuracy.
To find out for what is the point of a baitcaster line to throw, you need to know how fast you want to cast. You can estimate this by looking at the distance between you and the target.
Tyger Leader is reader-supported and may earn a commission when you book or purchase using our links. Learn more about our affiliate disclaimer here.
For example, if you’re fishing from shore, you probably don’t want to cast any further than 30 feet. If you’re fishing from a boat, you might want to go 50-60 feet.
If you’re using a sinking lure, you’ll want to add some weight to help slow the lure down. A good rule of thumb is to throw about 10% of your body weight behind the lure.
So, if you weigh 100 pounds, you’d throw 10 pounds of lead weight behind the lure.
If you’re using a fly, you’ll generally want to throw less line than you would with a sinking lure. In fact, you’ll usually only need enough line to just touch the surface of the water.
The reason for this is that flies tend to float rather than sink.
So, when you’re learning how to cast, try throwing one small loop first. Just make sure that your line doesn’t wrap around the reel handle.
If it does, simply pull it off and rewind it. Try again, and keep practicing until you get the hang of it.
You’ll also want to practice making smooth casts. Be careful not to jerk the rod back and forth like you were trying to hit something.
Instead, let the rod swing gently in an arc. As you gain more experience, you’ll become more comfortable with the technique.
Once you have mastered the art of proper casting, you’ll find that you can cast farther than ever before. And once you master that, you’ll be ready to tackle any type of fish you like.
Wrap Up
So, if you were to what is the point of a baitcaster follow all the simple steps provided, not only will you be able to set up your baitcaster, but you’ll also soon get the hang of casting.
People rarely get this right the first time, and it takes a little practice. But I assure you that with time, you’ll be point of baitcasting like a pro!
